McKeel Equipment, Kentucky
CASE IH
CASE CE
kubota
McKeel Equipment, Kentucky
Paducah
(270) 444-0110
1939 North 8th Street
Paducah, KY 42001
Call Us
Directions
Murray
(270) 753-3062
3724 US Highway 641 South
Murray, KY 42071
Call Us
Directions

Mowers LZS749AKC72400

New Products / Exmark / Mowers / Zero-Turn Mowers / LAZER Z S-SERIES / LZS749AKC72400

Double tap to zoom

 

Features

Doing More With Propane

Our EFI system optimizes fuel delivery in real-time, which improves efficiency and performance. This, in combination with lower propane cost reduces operating expenses versus typical gas-powered mowers.

Less Time At The Pump

Gas-powered S-Series models have a single 12-gallon tank with one fill location.

Built to Last

Want tough? Try a 10-gauge, formed and continuously seam-welded top, and a 7-gauge side skirt. All with welded spindle mounting sites. And, full-floating, 4-point suspension with four adjustable anti-scalp rollers.

On-Board Diagnostics

Check vital functions at a glance on the digital screen. An electronic fuel gauge with low fuel warning on all Lazer Z units, battery voltage warning, hour meter and OPC safety switch monitoring make troubleshooting easy.

Fewer Grease Points

With just four grease points that only need annual greasing, the Lazer Z delivers maximum performance with minimum maintenance. Grease-less spindles and only four grease points on the entire machine.

Ultracut Series 4 Deck

This full-floating deck uses maintenance free spindle with a splined blade driver to stop bolt tightening on impacts. And, our patented bearing design on idler arm pivots only needs annual service.

Tool-less Belt Removal

Deck and hydro belt can be installed without using any tools.

Specifications

Equipment  
Blade Spindles No maintenance, sealed and non-greasable spindles; 7.75"-diameter cutter housing with 25mm(.98") diameter spindle shaft and splined blade driver.
Drive Tires 24 x 12-12, Turf Master®
Cup Holder Standard
Tractor Frame Unibody, welded, heavy-duty 1.5" x 3" tubular steel.
Steering Control Hydraulically dampened twin levers, adjust fore and aft. Adjustable dampeners (3 positions) to customize drive responsiveness. Also adjustable to 2 height positions.
Front Caster Tires 13 x 6.5-6, smooth-tread, semi-pneumatic.
Parking Brake Lever-actuated disc brake.
Seat Deluxe, two tone, bolstered seat with Elastomeric Vibration Control material. Mounted on innovative Seat Isolation System that provides operator isolation in all three planes of motion as well as fore-aft slide and seat flip-up.
Electrical 12-volt battery with 20-amp alternator.
Power Components  
Engine Brand Kohler®
Engine Model ECV749
Engine Displacement 749
Engine Series Command™ EFI
Engine Type Electronic Fuel Injected
Engine Speed 3,750 rpm
Air Filter Heavy-duty canister air filtration system
Fuel Type Gas EFI
Fuel Capacity 12-gallon (45.4-L), single fuel tank with single fill location.
Fuel Indicator Yes - electronic Sender
Drive Hydro-Drive
Drive Description Two Exmark exclusive Parker unitized pump and wheel motor systems with no hoses, integrated cooling fans, shock valve, 1.7-quart integrated reservoir, spin-on filter and heavy-duty components. 12 cc pumps and 14. 5 cubic inch motors.
Speed Infinitely variable speed selection from 0-10.0 mph (16 kmph) forward, 0-6.0 mph (9.7 kmph) reverse.
Carb Compliant Yes
Deck Lift Standard; foot-controlled deck lift changes cutting height and lifts the deck to maneuver around obstacles, or place in transport position.
Safety Package Operator Presence Controls (OPC) and drive system interlock, with safety interlock system indicators.
ROPS 2-post foldable ROPS standard with seat belt and latch.
PTO Engagement MagStop electromagnetic 200-ft-lb clutch with spot brake
Drive Wheel Release Allows unit movement without engine running.
Casters .50" thick caster yoke arms.
Decks  
Width / Cutting Deck 72"
Deck Style Floating Deck
Deck Style Description Full-floating UltraCut Series 4. Side discharge standard, with molded discharge chute and option to bag or mulch.
Deck Construction 10-gauge top that is formed and continuously seam welded, 7-gauge side skirt and 7-gauge formed and welded spindle mounting locations for improved strength and reduced weight.
Blade Tip Speed Approximately 18,500 fpm.
Cutting Heights 1.0" (2.5 cm) to 5.5" (11.8 cm) in 0.25" (0.64 cm) increments adjustable from operator's seat.
Blades 3 Blades at 24.50" Length
Dimensions  
Width 84.9 in. (215.6 cm)
Length 86.1 in. (218.7 cm)
Height 70 in. (177.8 cm)
Curb Weight 1220